GaNS Production Kit

Preparation

Wear protective gloves.
In order to obtain the purest possible GaNS, it is necessary to prevent interactions between the containers; you can either space them more than 3m apart or make one GaNS at a time!
It is also important to reserve always the same container for a specific GaNS.
You can find more detailed instructions and information on GaNS production in this article.

GaNS-CO2

  1. Reserve a plastic container with a lid.
  2. Hang a plate or coil of nano-coated copper (Cu-nc) inside the container; the plate should not touch the bottom; use a cloth pin to hold it in place.
  3. Hang a plate of Zinc (Zn) on the opposite side of the copper plate
  4. Connect a green LED light between the 2 plates: the + of the LED (longer LED terminal) is connected to the Cu-np
  5. Fill the container with 3.5-10% salt water (use distilled water); fill up not higher than the rim of the plates

GaNS-ZnO

  1. Reserve a plastic container with a lid.
  2. Hang a plate or coil of nano-coated copper (Cu-nc) inside the container; the plate should not touch the bottom; use a cloth pin to hold it in place.
  3. Hang a plate of Zinc (Zn) on the opposite side of the copper plate
  4. Connect a simple copper wire between the 2 plates
  5. Fill the container with 3.5-10% salt water (use distilled water); fill up not higher than the rim of the plates

GaNS-CH3

  1. Reserve a plastic container with a lid.
  2. Hang a plate or coil of nano-coated copper (Cu-nc) inside the container; the plate should not touch the bottom; use a cloth pin to hold it in place.
  3. Hang a plate of galvanized steel (Fe-galvanized) on the opposite side of the copper plate
  4. Connect a simple copper wire between the 2 plates
  5. Fill the container with 3.5-10% salt water (use distilled water); fill up not higher than the rim of the plates

GaNS-CuO

  1. Reserve a plastic container with a lid.
  2. Hang a plate or coil of nano-coated copper (Cu-nc) inside the container; the plate should not touch the bottom; use a cloth pin to hold it in place.
  3. Hang a plate of Copper (Cu) on the opposite side of the copper plate
  4. Connect a simple copper wire between the 2 plates
  5. Fill the container with 3.5-10% salt water (use distilled water); fill up not higher than the rim of the plates

GaNS-spécifique

You can make and use the GANS of any substance, medication or supplement that is available to you.
To make GANS of medication or supplement (tablets or capsules), please follow these steps:

  • Capsules: Open the pill/vitamin capsule and pour the contents into a small container.
  • Tablets: Crush a hard tablet into a powder using a pill crusher and pour it into a small container.
  • Prepare the Ingredient Proportions:
    Fill a ¼ tsp. measuring spoon with powdered substance and place it in a mixing cup. Measure out ¼ tsp. of dry caustic (NaOH) and add it to the mixing cup (use a mixing cup or container that can be tightly sealed). Mix the powders well.
  • Start the Nano-coating Process: Add 5 tsp. of boiling water to the mixing cup and quickly tightly cover the container. The caustic (NaOH) will begin creating the nano material. Let stand, tightly sealed, for 3-7 days.
  • Wash the GANS Mixture: After 3-7 days have passed, open the container and wash the mixture with distilled water. (see below)
  • Add CO2 GANS: To finish the process, add some CO2 GANS (roughly 10ml) to the washed GANS. (CAUTION: never touch GANS with any part of the body).

You find more details on GaNS production in this article.

GaNS-perso

To produce a GaNS that is already geared towards your DNA, a GaNS that knows you, we use the technique to produce GaNS-CO2 adding some drops of your urine sample into the container.

GaNS washing

  1. Wear gloves and take all plates, wires and the DEL out of the container.
  2. Close the lid and let sediment over night.
  3. Open the lid ans pour the clear water into another container (you can dispose of this liquid in your garden etc.); take care not to let any GaNS spill.
  4. Fill the container again with distilled water; double de volume of the GaNS with water.
  5. Let it sit for a minium of 12 hours until the liquid above the GaNS is completely clear.
  6. Dispose of the clear liquid again; repeat the fill-discard process for 4 – 6 times.
  7. After washing transfer the liquid in a closed glass storage container and label it.

fabricator has written 40 articles